Lark Dezigns

Lark Dezigns Contact information, map and directions, contact form, opening hours, services, ratings, photos, videos and announcements from Lark Dezigns, Interior design studio, koottappillil house, Muvattupuzha.

Ergonomically designed interior spaces, Customised lighting solutions, Tables, art pieces with epoxy resin, Handmade decor products - clocks, lampshades, Jewellery, Trays, Keychains, etc

11/04/2026

This can be really frustrating…

You wait and wait…
But the resin just doesn’t cure 😅

Most of the time, it’s not a big mistake — just small things affecting the process.

This usually happens when:
• The room is too cold
• The ratio is slightly off
• Or the resin itself is slow-curing

What actually helps:
• Work in a warmer space
• Measure properly
• Check the resin type before using

Once you fix this, curing becomes much more predictable.

Save this so you don’t forget, and follow for more resin tips.
Next I’ll show you if you can speed up resin curing 👀

📞 8547426232 / 9745261828
📲 https://www.instagram.com/larkdezigns?igsh=YzBsY3Vma29yOTJm

📝 Voiceover is generated using AI. If there is any mistake, please comment.

This can be really frustrating…

You wait and wait…
But the resin just doesn’t cure 😅

Most of the time, it’s not a big mistake — just small things affecting the process.

This usually happens when:
• The room is too cold
• The ratio is slightly off
• Or the resin itself is slow-curing

What actually helps:
• Work in a warmer space
• Measure properly
• Check the resin type before using

Once you fix this, curing becomes much more predictable.

Save this so you don’t forget, and follow for more resin tips.
Next I’ll show you if you can speed up resin curing 👀

📞 8547426232 / 9745261828
📲 https://www.instagram.com/larkdezigns?igsh=YzBsY3Vma29yOTJm

📝 Voiceover is generated using AI. If there is any mistake, please comment.

resin curing time, resin curing slow, epoxy curing problem, resin not curing fast, resin temperature issue, resin ratio problem, epoxy resin tips, resin beginner tips, diy resin tips, resin troubleshooting, resin hacks, epoxy resin India

10/04/2026

Hard resin… but soft spots? This is why 👇

This one confuses a lot of beginners…

The resin looks perfect…
But suddenly you find soft or rubbery spots 😅

Most of the time, it’s not the resin — it’s the mixing.

This usually happens when:
• The resin is not mixed properly
• The sides and bottom were not scraped
• Or the ratio was slightly off

What actually helps:
• Mix slowly and thoroughly
• Don’t rush the process
• Make sure everything is evenly combined

Once you fix this, your resin will cure properly everywhere.

Save this so you don’t forget, and follow for more resin tips.
Next I’ll show you why resin takes too long to cure 👀

📞 8547426232 / 9745261828
📲 https://www.instagram.com/larkdezigns?igsh=YzBsY3Vma29yOTJm

📝 Voiceover is generated using AI. If there is any mistake, please comment.

09/04/2026

Why are there tiny holes in your resin? 😳

This is one of those things that suddenly appear…
And completely ruin the finish 😅

Tiny holes or spots in resin usually happen because of something very small — dust, oil, or even fingerprints.

Most beginners don’t realize this at first.

What actually helps:
• Always clean your surface before pouring
• Avoid touching it with bare hands
• Keep your molds and tools clean

Once you fix this, your finish becomes much smoother.

Save this so you don’t forget, and follow for more resin tips.
Next I’ll show you why soft spots happen 👀

📞 8547426232 / 9745261828
📲 https://www.instagram.com/larkdezigns?igsh=YzBsY3Vma29yOTJm

📝 Voiceover is generated using AI. If there is any mistake, please comment.

08/04/2026

Resin forming waves? This is why 👇

You pour everything perfectly…
And then the surface turns wavy 😅

This is actually a very common issue.

Most of the time, it happens because:
• The surface is slightly tilted
• The piece was moved during curing
• Or air from a fan disturbed the resin

What actually helps:
• Always check if your surface is level
• Don’t touch or move it while curing
• Keep it away from airflow

Small changes like this can completely improve your finish.

Save this so you don’t forget, and follow for more resin tips.
Next I’ll show you why dimpling happens 👀

📞 8547426232 / 9745261828
📲 https://www.instagram.com/larkdezigns?igsh=YzBsY3Vma29yOTJm

📝 Voiceover is generated using AI. If there is any mistake, please comment.

07/04/2026

This is one of those things that looks perfect…
until you remove it from the mold 😅

And then you see bubbles trapped inside…

This usually happens when:
• You pour too fast
• The mold is deep
• Or you didn’t prepare the surface properly

What actually works:
• Pour slowly and steadily
• Apply a thin layer first inside the mold
• Use heat to release trapped air

Once you start doing this, your finish becomes much cleaner.

Save this for later and follow for more resin tips.
Next I’ll show you why resin leaks from molds 👀

📞 8547426232 / 9745261828
📲 https://www.instagram.com/larkdezigns?igsh=YzBsY3Vma29yOTJm

📝 Voiceover is generated using AI. If there is any mistake, please comment.

07/04/2026

This is one of the most frustrating moments…

You pour everything perfectly…
And then suddenly resin starts leaking 😅

Most of the time, it’s not your mixing — it’s the mold setup.

This usually happens when:
• There are small gaps or cracks
• The mold is low quality
• Or the surface is not flat

What actually helps:
• Always check molds before pouring
• Seal small gaps using tape
• Keep the surface completely flat

Once you fix this, your pouring becomes stress-free.

Save this so you don’t forget, and follow for more resin tips.
Next I’ll show you why resin forms uneven surfaces 👀

📞 8547426232 / 9745261828
📲 https://www.instagram.com/larkdezigns?igsh=YzBsY3Vma29yOTJm

📝 Voiceover is generated using AI. If there is any mistake, please comment.

06/04/2026

This is one mistake almost everyone makes at the beginning…

You pour the second layer…
And either it mixes completely or doesn’t stick at all 😅

The truth is — timing matters more than anything.

If you pour too early, everything blends.
If you pour too late, it won’t bond properly.

What actually works:
• Pour when the surface feels slightly sticky (not wet)
• If it’s fully hard, just sand it lightly before pouring

Once you understand this, your layering will become much cleaner and more professional.

Save this for later and follow for more resin tips.
Next I’ll show you why resin sticks to molds 👀

📞 8547426232 / 9745261828
📲 https://www.instagram.com/larkdezigns?igsh=YzBsY3Vma29yOTJm

📝 Voiceover is generated using AI. If there is any mistake, please comment.

06/04/2026

This is one of the most frustrating things…

You finish your piece…
And it just won’t come out of the mold 😅

Most of the time, it’s not your fault — it’s the setup.

This usually happens when:
• The mold is not proper silicone
• You didn’t use any release
• Or you tried removing it too early

What actually works:
• Always use good silicone molds
• Use mold release when needed
• Wait patiently until it fully cures

Once you follow this, demolding becomes super easy.

Save this so you don’t forget, and follow for more resin tips.
Next I’ll show you why bubbles form inside molds 👀

📞 8547426232 / 9745261828
📲 https://www.instagram.com/larkdezigns?igsh=YzBsY3Vma29yOTJm

📝 Voiceover is generated using AI. If there is any mistake, please comment.

05/04/2026

If your resin shrank after curing… you’re not alone.
This is something almost everyone faces at some point.

At first, I thought I did something completely wrong.
But actually, resin naturally shrinks a little during curing — the real problem is when it becomes too noticeable.

This usually happens when:
• You pour thick layers
• You use low-quality resin
• Or the curing conditions are not stable

Here’s what really helps:
• Always pour in thin layers
• Give enough time for curing
• Try to maintain a consistent room temperature

Once you start doing this, your results will improve a lot.

Save this for later and follow for more resin tips.
Next I’ll show you if you can pour a second layer on resin 👀

📞 8547426232 / 9745261828
📲 https://www.instagram.com/larkdezigns?igsh=YzBsY3Vma29yOTJm

📝 Voiceover is generated using AI. If there is any mistake, please comment.

03/01/2026

Litchenburg/ fractal wood burning

Address

Koottappillil House
Muvattupuzha
686671

Telephone

+919745261828

Website

Alerts

Be the first to know and let us send you an email when Lark Dezigns posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Lark Dezigns:

Shortcuts

Share

Category