Garth Industries Gippsland Rescued timber slabs

Garth Industries Gippsland Rescued timber slabs this timber would be going to fire wood, tip , burn pile .

I collect it , mill it , dry it , for those people who work with and love the look of timber.this is storing carbon.

This is a money box for owen my grandson,there are 6 different timbers all reclaimed from local area
31/08/2024

This is a money box for owen my grandson,there are 6 different timbers all reclaimed from local area

Have not posted for a while.this is a bar I made for Jake Kurnels 21st, local cypress with mini orb front,live edge slab...
31/08/2024

Have not posted for a while.this is a bar I made for Jake Kurnels 21st, local cypress with mini orb front,live edge slab top,and his letters in blackwood.

Made a cigar box for corey, butterfly cut silky oak 1/4 sawn realy nice grain 19 bits of wood in this
19/01/2024

Made a cigar box for corey, butterfly cut silky oak 1/4 sawn realy nice grain 19 bits of wood in this

03/07/2022

Sorry this bar top was in darwin

This is a bar top it is african mahogny  found the bloke that probably cut it,got some small bits for pens ,1 bit of fig...
03/07/2022

This is a bar top it is african mahogny found the bloke that probably cut it,got some small bits for pens ,1 bit of figured crotch .i should get about 10 pens from it.the variations of colour are reverse grain ,so a lot of sanding to get it right .i will post finished job if ok.

Made this for my granddaughter  queensland cypres hollow form with 3 marbles inside makes a nice noise.
29/05/2022

Made this for my granddaughter queensland cypres hollow form with 3 marbles inside makes a nice noise.

This was for phill and kaitlin PKN Auto, towel rail nearly 2mt long cypress timber free hand shape front rail reversed t...
30/03/2022

This was for phill and kaitlin PKN Auto, towel rail nearly 2mt long cypress timber free hand shape front rail reversed to enhance shape ,finish tung oil 4 coats . cups for screws turned red box , fixing 175 mm gal hex head decking screws . The lump on left end is next to shower ,to hang towel ready for when you get out.house warming present

Did this one for birthday present back board cypress letters silky oak light patches sap wood finish is tung oil.
30/03/2022

Did this one for birthday present back board cypress letters silky oak light patches sap wood finish is tung oil.

So vacume pump from old fridge motor, made vacume chamber from vacola bottles turned timber with silicon  seal rubber b*...
21/11/2021

So vacume pump from old fridge motor, made vacume chamber from vacola bottles turned timber with silicon seal rubber b**g to release vacume blocks wood 20 mm holes turned down banksia cones ,put in wood added resin with gold pearl into chamber .pulled vac popped plug a few times to let pressure force resin into cone.rough cut timber ,put in lath ,rough turn down ,drilled wholes for brass inserts .have let it harden up for week, ready to start making 4 banksia cone pens .these cones are specal only found 4 trees of this species in lakes entrance they are very heavy and dense so turn well.

I started out with the pencil case out of QLD cypres (murry pine). came up realy nice, so next is a needle case for her ...
18/11/2021

I started out with the pencil case out of QLD cypres (murry pine). came up realy nice, so next is a needle case for her wool needles. a bit off fiddle back red gum from denison, it was cut for pen blank so ended up about 100mm long x 20mm dia , slightly loose on lid might try a cotton wip like they do on the reed of bagpipes , i will coat with bees wax not spit see if that tightens it up

Made this for Zoe's birthday will have photos stuck all over it . And I got a new toy as well,sharpen my band saw blade ...
14/10/2021

Made this for Zoe's birthday will have photos stuck all over it . And I got a new toy as well,sharpen my band saw blade enough times you run out set on teeth does not cut very well

Here is how the floors came up my piece of banksia nut inlaid to fill a hole came up quite nice
01/08/2021

Here is how the floors came up my piece of banksia nut inlaid to fill a hole came up quite nice

Address

Bairnsdale, VIC
3875

Telephone

+61417387922

Website

Alerts

Be the first to know and let us send you an email when Garth Industries Gippsland Rescued timber slabs posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Garth Industries Gippsland Rescued timber slabs:

Share