Key house in pokhara

07/05/2026

Xtool sacnner obd 2 को बारेमा केहि जानकारी
फ़ोन 984-6042291
30X Wireless Scan Tool
This user manual is applicable to A30X
Shenzhen Xtooltech Intelligent Co., LTD
Version 1.1 | 2025.08 Please read this user manual carefully before using the Anyscan+ Wireless Scan
Tool. When reading the manual, please pay attention to the words “Note” or
“Caution” and read them carefully for appropriate operation. TRADEMARKS
and Anyscan® are the registered trademarks of Shenzhen Xtooltech
Intelligent CO., LTD.
In countries that the trademarks, service marks, domain names, logos, and the
name of the company are not registered, XTOOL claims that it still reserves the
ownership of the unregistered trademarks, service marks, domain names, logos, and the company name. All other marks for the other products and the company’s
name mentioned in the manual still belong to the original registered company. You may not use the trademarks, service marks, domain names, logos, and
company name of XTOOL or other companies mentioned without written permission
from the trademark holder. XTOOL reserves the right to the final interpretation of this manual content. COPYRIGHT
Without the written consent of Shenzhen Xtooltech Intelligent Co., Ltd., any
company or individual shall not copy or backup this operation manual in any form
(electronic, mechanical, photocopying, recording, or other forms). DECLARATION
This manual is designed for the usage of the Anyscan+ Wireless Scan Tool and
provides operating instructions and product descriptions for users of the Anyscan+
Wireless Scan Tool. No part of this manual can be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), without the prior written permission of XTOOL. Use the device only as described in this manual. XTOOL is not responsible for any consequences of violating the laws and regulations caused by using the product or
its data information
XTOOL shall not be liable for any incidental or consequential damages or for any
economic consequential damages arising from the accidents of individual users and
the third parties, misuse or abuse of the device, unauthorized change or repair of
the device, or the failure made by the user not to use the product according to the
manual. The configuration, function, appearance and UI of this product involved in the user
manual will continue to be optimized, and the manual may not be updated in time. Please refer to the actual product if there is any difference. The final interpretation
right belongs to Shenzhen Xtooltech Intelligent Co., Ltd. OPERATION INSTRUCTIONS
For safe operation, please follow the instructions below:
 Keep the device away from heat or fumes when you are using it.  If the vehicle battery contains acid, please keep your hands and skin or fire
sources away from the battery during testing.  The exhaust gas of the vehicle contains harmful chemicals, please ensure
adequate ventilation.  Do not touch the cooling system components or exhaust manifolds when the
engine is running due to the high temperatures reached.  Make sure the car is securely parked, Neutral is selected or the selector is at P
or N position to prevent the vehicle from moving when the engine starts.  Make sure the (DLC) diagnostic link connector is functioning properly before
starting the test to avoid damage to the Diagnostic Tablet.  Do not switch off the power or unplug the connectors during testing, otherwise, you may damage the ECU and/or the Diagnostic Tablet. CAUTIONS
 Avoid shaking or dismantling the unit as it may damage the internal components.  Do not use excessive force;
 Please keep it away from water, moisture, high temperature, or very low
temperature;
 Keep the main unit away from strong magnetic fields. AFTERSALES-SERVICES
E-Mail: [email protected]
Tel: +86 755 21670995 or +86 755 86267858 (China)
Official Website: www.xtooltech.com
Please provide your device serial number, VIN code, vehicle model, software version, and other
details when seeking technical support.
If there are screenshots or videos, it will better help us locate your problem. Contents
1 General Introduction............................................................................................................................ 1
1.1 Appearance & Interfaces...............................................................................................................1
1.2 Technical Specifications................................................................................................................2
1.3 Wireless Communication.............................................................................................................. 2
2 Product Activation................................................................................................................................. 3
2.1 Download & Install APP.................................................................................................................3
2.2 Create Account & Log in............................................................................................................... 3
2.3 Activate Device...................................................................................................................................4
2.4 Vehicle Connection.......................................................................................................................... 4
2.5 Bluetooth Connection......................................................................................................................6
2.5.1 IOS Bluetooth Connection..........................................................................................................6
2.5.2 Android Bluetooth Connection...................................................................................................7
2.6 Download & Update Software.................................................................................................... 8
3 Product Usage........................................................................................................................................... 9
3.1 Diagnostics Function....................................................................................................................... 9
3.1.1 Auto Scan........................................................................................................................................9
3.1.2 Diagnosis...................................................................................................................................... 10
3.1.3 Diagnosis Functions...................................................................................................................12
3.1.4 OBDⅡ........................................................................................................................................... 17
3.1.4.1 Read Freeze Frame.............................................................................................................. 18
3.1.4.2 Component Test....................................................................................................................18
3.1.4.3 On-Board Monitor Test..........................................................................................................18
3.1.4.4 O2 Sensor Monitoring Test................................................................................................... 18
3.1.4.5 I/M Readiness ........................................................................................................................18
3.1.5 Special Functions........................................................................................................................19
3.1.5.1 Oil Reset................................................................................................................................ 19
3.1.5.2 EPB........................................................................................................................................ 20
3.2 Vehicle Test........................................................................................................................................21
3.2.1 Performance Test....................................................................................................................... 21
3.2.2 Smog Check................................................................................................................................ 22
3.2.3 Mode 6...........................................................................................................................................23
3.2.4 Malfunction Indicator Lamp Status.........................................................................................24
3.3 General Functions.......................................................................................................................... 25
3.3.1 Vehicle Coverage....................................................................................................................... 25
3.3.2 Report............................................................................................................................................26
3.3.3 CSV View......................................................................................................................................27
3.4 Technical Data..................................................................................................................................29
3.4.1 OBD DTC Query.........................................................................................................................29
3.4.2 Warning Light Symbols............................................................................................................. 30
3.4.3 Technical Bulletin........................................................................................................................31
3.4.4 Recall Notice................................................................................................................................32
3.4.5 Safety Rating............................................................................................................................... 33
3.5 Setting................................................................................................................................................... 34
3.5.1 Firmware Upgrade......................................................................................................................34
3.5.2 Software Management.............................................................................................................. 35
3.5.3 Language Settings..................................................................................................................... 36
3.5.4 Unit Settings.................................................................................................................................37
3.5.5 About..............................................................................................................................................38 4 Compliance Information..................................................................................................................39
FCC Compliance..................................................................................................................................... 39
ISED Statement........................................................................................................................................40
CE....................................................................................................................................................................41
UKCA............................................................................................................................................................. 41 1
1 General Introduction
1.1 Appearance & Interfaces
A30X is a full system scan tool and easily to carry in your pocket, working together
with mobile phones. Both iOS and Android platforms are supported. The A30X
package includes a Bluetooth OBDII connector and an Anyscan+ application. It is a
perfect DIY tool for customers to get a quick scan of all systems and full brands are
covered. It also includes numerous special functions, such as service light reset, DPF regeneration, and EPB reset.
① OBDⅡ Port
② Indicator Light
③ Lanyard Hole 2
1.2 Technical Specifications
Technical parameters Description
Dimensions 86.2 × 50.0 × 22.4（mm）
Operating Temperature 0℃ ~ 40 ℃
Input Voltage Range 9~36V DC
Communication Protocol BT 5.0
Indicator Light
Solid green light—Powered on
Flashing green light—Firmware updating
Solid blue light—Device connected (no communication)
Flashing blue light—Communicating with the vehicle
Flashing red light—Device fault
1.3 Wireless Communication
A30X uses Bluetooth communication. It can transmit vehicle data to your Android
or IOS device without a physical connection. The working range for Bluetooth is
around 10 m (32.81 ft.). Signal lost due to moving out of the range will
automatically be restored once the device is brought within transmission range to
the A30X connector. 1.4 Power Source
A30X operates on 12-volts vehicle power which it receives through the vehicle data
connection port. The unit powers on whenever it is connected to an OBDII compliant
data link connector (DLC). 3
2 Product Activation
2.1 Download & Install APP
Scan the QR codes shown below to download the Anyscan+ application install
package. You will be directed to the corresponding downloading page.
2.2 Create Account & Log in
Enter your email to get a verification code, then complete the registration and log in
to your account. 4
2.3 Activate Device
Open "My Devices" to add a new device. You can scan the QR code on the device
or manually enter the S/N and activation code.
2.4 Vehicle Connection
Insert the A30X to the OBD port on the testing vehicle, diagram below shows the
common locations where the OBD port at. The flashlight equipped may help to
locate the OBD port. Green light will be shown on the power indicator if the device is
properly connected. 5
Precautions for Diagnosis
1. The voltage range on the car: +9~+36V DC;
2. When testing some special functions, the operator must operate according to the
prompts and meet the test conditions. For some models [special functions], the
conditions that need to be met are: engine water temperature 80 ℃~105 ℃, turn off
headlights and air conditioners, keep the accelerator pedal in the released position, etc.;
3. The electronic control systems of different models are very complicated. If you
encounter situations where it is impossible to test or a large amount of test data is
abnormal, you can search for the ECU of the vehicle and select the menu for the
model on the ECU nameplate;
4. If the vehicle type or electronic control system to be tested is not found in the
diagnostic function, please upgrade the vehicle diagnostic software to the latest
version using the Updates menu or consult the XTOOL technical service department;
5.When running a Diagnostics function, it is forbidden to shut down the device
directly. You should cancel the task before returning to the main interface and then
shutting down the device. 6
2.5 Bluetooth Connection
Connection Status Graphic Meaning
Searching for device
Device not connected
Device connected
2.5.1 IOS Bluetooth Connection
Click the VCI icon in the upper right corner, and the APP will redirect to your mobile
device's Bluetooth list. You'll see device Bluetooth named with the 'A30X' prefix, which you can manually connect to. Upon successful Bluetooth connection, the
device's solid green light will turn blue accompanied by a 'beep' sound, while the
APP icon will change accordingly.
You are only able to connect the Bluetooth after connecting the Anyscan+ to the vehicle/power 7
supply. For Android users, you may need to pair the Anyscan+ device in the system setting of your
phone before you can connect the device within the app. 2.5.2 Android Bluetooth Connection
After activating the device, entering the Anyscan+ APP will automatically request
Bluetooth activation to pair with your bound A30X device. Successful pairing will
trigger automatic scan and connection. When Bluetooth connection is established,
the device's solid green light will turn blue with a 'beep' sound, and the APP icon will
update simultaneously. 8
2.6 Download & Update Software
All the available software is shown on this page. You can choose to download the
specific software individually by pressing the arrow button next to the required
software or choose to upgrade all available software at once by pressing Updates
All.
The DG_AOBD package must be downloaded before using Vehicle Test module. 9
3 Product Usage
3.1 Diagnostics Function
The diagnosis function can read ECU information, read and clear DTC and display
live data and freeze frame. The diagnosis function can also access the electronic
control unit (ECU) of all available vehicle control systems, including the engine,
transmission, anti-lock braking system (ABS), airbag system (SRS), body control
module (BCM), battery management system (BMS), tire pressure monitoring system
(TPMS), steering and suspension system (SAS) and perform various actuation tests. 3.1.1 Auto Scan
Click the AUTO SCAN button, and the models and information will be scanned. You
have to select the corresponding options and confirm the vehicle information
scanned.
After clicking the AUTO SCAN, if the required software is not installed, you will be directed the
updates page of that software. Automatic Detection does not work on all cars. If ‘Automatic Detection’ fails, it does not 10
necessarily mean that your vehicle or the function is not supported, please navigate manually
and try again. 3.1.2 Diagnosis
Click the Diagnosis button on the main screen and get into the diagnosis menu. All
the brands will be shown on the screen, you can select the region of your vehicle, click the correct brand, and start the diagnosis process.
For some of the vehicle brands (like Volkswagen), when you click on the software,
there are several ways to select the model or system you want to run a diagnosis,
including Automatic Detection, Manual Selection, and System Selection. 11
Automatic Detection will automatically identify the vehicle’s VIN code, and then read
the information of your target diagnostic vehicle. (Same function as AUTO SCAN on
the main menu) If you choose Manual Selection, then you can continue to select the
vehicle brand, year, and model of the vehicle in the sub-menu to diagnosis the
vehicle. OBDII menu supports reading the common fault codes in the PCM. The DTCs may not be the
same when compared with using common diagnosis software. DEMO is a demonstration program. You can perform basic diagnosis functions without connecting
to the car. DEMO is only for demonstration purposes, the functions and interface are not necessarily the
same as the actual version of the software/App. Please activate and update your device to use
the latest version of software. 12
3.1.3 Diagnosis Functions
The Diagnosis System supports 5 basic diagnosis functions:
 Read ECU Information
 Read & Clear Trouble Code
 Live Data
 Actuation Test (Bi-Directional Control)
 Freeze Frame
3.1.3.1 Read ECU Information
This function is to read ECU version information, which is the equivalent of System
Identification or System Information in some electronic control systems, which
means to read ECU-related software and hardware versions, models, and
production date of the diesel engine, part number, etc. 13
3.1.3.2 Read Trouble Code
Read trouble codes (DTCs) that are stored in ECU. For the trouble code, the
diagnostic instrument will give specific detailed definitions and explanations to help
you locate and eliminate the car fault.  Stored Code
Stored codes are the current emission-related DTCs from the ECM of the
vehicle. OBDII Codes have a priority according to their emission severity, with
higher priority codes overwriting lower priority codes. The priority of the code
determines the illumination of the MIL and the codes erase procedure. Manufacturers rank codes differently, so expect to see differences between
makes.  Permanent Codes
Permanent DTCs are emission-related fault codes mandatorily stored in the
ECU's non-volatile memory in the vehicle's OBD-II system. A key
characteristic is that they are not erased when power is disconnected and
cannot be cleared by standard diagnostic tools. These codes are only cleared
automatically after the system verifies the fault has been repaired by
completing a manufacturer-specified drive cycle. Failure to clear a permanent 14
DTC will result in an emissions test failure, as it serves as a non-erasable
record of a critical fault mandated by environmental regulations.  Pending Code
These are codes whose setting conditions were met during the last drive
cycle, but need to be met two or more consecutive drive cycles before
the DTC actually sets. The intended use of this service is to assist the service
technician after a vehicle repair and after clearing diagnostic information, by
reporting test results after a driving cycle. a. If a test failed during the driving cycle, the DTC associated with that
test is reported. If the pending fault codes do not occur again within 40
to 80 warm-up cycles, the fault is automatically cleared from memory. b. Test results reported by this service do not necessarily indicate a faulty
component or system. If test results indicate another failure after
additional driving, then a DTC is set to indicate a faulty component or
system, and the MIL is illuminated.
In the process of diagnosis, if the device shows “System is OK” or “No Trouble Code”, it means
there is no related trouble code stored in ECU. OR some troubles are not under the control of
ECU, most of these troubles are mechanical system troubles or executive circuit troubles, it is
also possible that the signal of the sensor may bias within limits, which can be determined by Live
Data. 15
3.1.3.3 Clear Trouble Code
It allows clearing current and historical trouble codes (DTCs) memory in ECU, under
the premise that all the troubles are eliminated. There are two types of trouble codes, one is permanent trouble code and the other is non-permanent trouble code. The
former requires manual troubleshooting of the car before it can be cleared with a
diagnostic tool. Non-permanent trouble codes can be cleared directly with the
diagnostic tool.
The trouble codes cannot be cleared without eliminating all the troubles, the diagnostic tool can
always read those codes as those codes are saved in ECU. 16
3.1.3.4 Live Data
This function displays the real-time parameters of the ECU, take the engine as an
example, parameters such as engine oil temperature, engine speed, ambient
pressure, coolant temperature, etc. can be read. The Scope of maintenance can be
narrowed down as we can determine the faulty component based on these
parameters. And the data can be displayed in various modes.
3.1.3.5 Actuation Test
Actuation test, also known as bidirectional control, is a generic term used to
describe sending and receiving information between one device and another. The
scan tool can request information or command a module to perform specific tests or
functions. Some manufacturers refer to the bidirectional controls as function tests, actuation tests, inspection tests, system tests. Reinitialization and reprogramming
would also be included in the list of bidirectional controls. Most enhanced scan tools
also can actuate relays, injectors, and coils, perform system tests, etc. Users could
check the individual part to see which part is working properly by actuation test. 17
3.1.4 OBDⅡ
The OBDII (On-board diagnostics) refers to the vehicle’s self-diagnostic and
reporting ability. When the malfunction of any sub-systems is detected, relevant MIL
is illuminated and notice the vehicle owner or repair technician the status of the
vehicle. OBDII implements the standardized digital communications port and
diagnostic trouble codes (DTCs) which allows scan tools to communicate with the
PCM of the vehicle. And the Anyscan+ is able to access the OBDII diagnostic
functions as follows:
 Read & Clear Trouble Codes
 Live Data
 Read Freeze Frame
 Read ECU Information
 Component Test
 On-Board Monitor Test
 O2 Sensor Monitoring Test
 I/M Readiness
Red Trouble codes ,Clear Trouble Codes ,Read ECU Information and Live Data are the same as
Diagnosis Function. 18
3.1.4.1 Read Freeze Frame
In most cases, the stored frame is the last DTC that occurred. Certain DTCs, which
have a greater impact on vehicle emission, have a higher priority. In these cases,
the top prioritized DTC is the one for which the freeze frame records are
retained.Freeze frame data includes a “snapshot” of critical parameter values at the
time the DTC is set. 3.1.4.2 Component Test
This service enables bi-directional control of the ECM so that the diagnostic tool is
able to transmit control commands to operate the vehicle systems. This function is
useful in determining whether the ECM responds to command well. 3.1.4.3 On-Board Monitor Test
This option allows you to view the results of On-Board Monitor tests. The tests are
useful after servicing or after erasing a vehicle’s control module memory. 3.1.4.4 O2 Sensor Monitoring Test
The oxygen sensor monitor allows the PCM to verify that the O2 sensors are
properly calibrated and functioning without noticeable deterioration under normal
engine operating conditions. 3.1.4.5 I/M Readiness
This function is used to check the readiness of the monitoring system. It is an
excellent function to use prior to having a vehicle inspected for compliance with a
state emissions program. Selecting I/M Readiness opens a submenu with two
choices:
 Since DTCs Cleared – displays the status of monitors since the last time
the DTCs are erased.  This Driving Cycle – displays the status of monitors since the beginning
of the current drive cycle. 19
3.1.5 Special Functions
Special functions allow you to quickly access your vehicle system for various
scheduled services, maintenance and reset performance, eliminating the need to
reset after resolving common problems. This user manual lists some commonly
used special reset services for your reference. The special function interface is
shown as below:
All software screens shown in this manual are examples, actual test screens may vary for each
vehicle being tested. Observe the menu titles and on-screen instructions to make correct option
selections. 3.1.5.1 Oil Reset
Reset the Engine Oil Life System, which calculates the optimum oil life change interval
based on the vehicle’s driving conditions and climate. The oil life reminder must be
reset each time the oil is changed so that the system can calculate when the next oil
change is required. This function can be performed in the following cases:
 If the service lamp is on, you must provide service for the car. After service, you
need to reset the driving mileage or driving time so that the service lamp turns off 20
and the system enables the new service cycle.  After changing engine oil or electric appliances that monitor oil life, you need to
reset the service lamp. 3.1.5.2 EPB
Electronic Parking Brake (EPB) System reset is a popular special function. You can
use this function to reset the electronic parking brake system and brake pads, which
also supports the brake pad replacement (retraction, release of the brake pump), G- sensor, and body angle calibration. This function has multiple uses and can safely and
effectively maintain the electronic brake system. These applications include
deactivating and activating brake control systems, assisting in controlling brake fluid, opening and closing brake pads, and setting brakes after replacing brake discs or
brake pads, etc. 1. If the brake pad wears the brake pad sense line, the brake pad sense line will send a
signal to the onboard tablet asking for replacing the brake pad. After replacing the
brake pad, you must reset the brake pad. Otherwise, the car alarms. 2.Reset must be performed in the following cases:
 The brake pad and brake pad wear sensor are replaced.  The brake pad indicator lamp is on.  The brake pad sensor circuit is short, which is recovered.  The servo motor is replaced. 21
3.2 Vehicle Test
The DG_AOBD package must be downloaded before using Vehicle Test module
3.2.1 Performance Test
This function monitors the vehicle's dynamic performance indicators in real time, providing a quantitative basis for service diagnostics and performance optimization.
It enables powertrain health assessment through key parameters such as RPM,
temperature, and load, pinpoints potential engine faults, and calibrates acceleration
performance and safety thresholds. 22
3.2.2 Smog Check
Based on EPA standards and state-level emissions testing regulations, this function
can pre-verify if a vehicle will pass an official emissions inspection and perform
multi-dimensional diagnostics. It can also accurately identify faults, distinguishing
between "Permanent DTCs" and "Temporary Not Ready" statuses, and
automatically saves inspection reports (including time, date, and pass/fail status) for
historical tracking. 23
3.2.3 Mode 6
Mode 6 is one of the nine standard modes of the OBD2 system. Unlike other modes
that provide real-time and stored data, Mode 6 retrieves test results for emission-
related powertrain components and systems that are not continuously monitored by
the vehicle's onboard computer. It reports the results of tests conducted by the
vehicle manufacturer, covering various systems such as Oxygen Sensors, Catalytic
Converters, and more. 24
3.2.4 Malfunction Indicator Lamp Status
This function tracks the historical status of the Malfunction Indicator Lamp (MIL) and
vehicle operating parameters in real time. This allows for quantifying the duration of
a fault by precisely recording when the MIL was triggered, verifying the effectiveness
of repairs by comparing run time/mileage data before and after clearing codes, and
predicting latent issues by capturing the trigger patterns of intermittent faults. 25
3.3 General Functions
3.3.1 Vehicle Coverage
You can tap "Vehicle Coverage" to look up the supported system diagnostic
functions and their sub-functions within a specific vehicle model's diagnostic
package. You can complete the query by selecting "Diagnostics" or "Special
Functions," then choosing the desired brand, model, year, system, and sub-function. 26
3.3.2 Report
This feature provides a history of diagnostic reports, where you can view and delete
the vehicle's diagnostic reports according to your needs. When you finish the
diagnostics progress and exit the diagnostic application specific to this vehicle, you
will get a prompt of report regeneration.
When you open the report, located in the header of the table is the information of the
vehicle, as shown below: 27
You also can click "Print PDF Report" at the bottom right corner to output the pdf
report. If you need to close the report tap on the button “Exit”. 3.3.3 CSV View
This function allows you to replay the Live Data recorded during the diagnosis
process. The data will only be recorded when you have pressed the Data
Recording button and valid data were shown when performing the Live Data
function.
You can play/pause the video and swipe to view all the data recorded. 28 29
3.4 Technical Data
3.4.1 OBD DTC Query
This function is used to quickly look up OBD (On-Board Diagnostics) DTC
(Diagnostic Trouble Code), helping users to precisely identify the system to which
the fault pertains (e.g., engine, body, battery); obtain detailed explanations of the
fault by code or category; and assist in diagnostic procedures to improve
troubleshooting efficiency.
You can search directly using the prompt in the search box: Search fault code . You can also select: Main category-Sub-category- Select DTC, then view its detailed
description. 30
3.4.2 Warning Light Symbols
This function analyzes vehicle dashboard warning lights, helping users to quickly
match the illuminated icon with its risk level, determine the urgency of the fault by
color (red/yellow), and provides the cause of the fault. 31
3.4.3 Technical Bulletin
Provides technicians/vehicle owners with the latest Technical Bulletin from the
manufacturer, allowing them to: filter technical solutions related to vehicle faults by
model, trace original documents by bulletin number (e.g., LTR 110317), and obtain
official manufacturer repair recommendations and component replacement guides. You can select Brand - Model - Year. 32
3.4.4 Recall Notice
This function quickly checks if a vehicle is part of a manufacturer recall campaign, ensuring driving safety. You can select Brand - Model - Year. 33
3.4.5 Safety Rating
This function provides multi-dimensional safety analysis for vehicle models, allowing
you to query and obtain the vehicle's safety rating. You can select Brand - Model - Year. 34
3.5 Setting
3.5.1 Firmware Upgrade
You can upgrade the A30X's firmware here. 35
3.5.2 Software Management
This function allows you to manage the diagnostic packages used for custom
procedures (such as throttle adaptation, TPMS reset, etc.) and to delete
unnecessary packages to free up storage space. 36
3.5.3 Language Settings
The languages supported by the device are listed in Setting. The default language
is set as English, if you need to switch to other languages, please contact the dealer
to unbind the current language configuration and rebind it to the language
configuration you need to switch. After the configuration is successfully changed, you can switch the target language. 37
3.5.4 Unit Settings
You can switch the units shown in the system on your preference. Anyscan+ provides
you with Metric, Imperial, and U.S. units. You can directly click on the preferred units, after it switches successfully, a blue tick symbol will be shown behind that unit’s
name. 38
3.5.5 About
You can check the APP version, User Agreement Privacy, Privacy Policy and
Contact us here. 39
4 Compliance Information
FCC Compliance
FCC ID: 2AW3IA01B1
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1) This device may not cause harmful interference
2) This device must accept any interference received, including interference that
may cause undesired operation. Warning
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. Note
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment can generate, use and radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
 Reorient or relocate the receiving antenna.  Increase the separation between the equipment and the receiver.  Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. 40
Responsible Party
Company name: FCC US Agent, LLC
Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA
E-mail:[email protected]
Company Name:Canadian certification consulting, Inc. Address: 2210 Horizon Drive, Suite 17West Kelowna, BC V1Z 3L4, Canada
Email: [email protected]
ISED Statement
IC: 29441-A01B1
Model: Anyscan A30X
PMN: Wireless Diagnostics Module, Vehicle Communication Interface
HVIN: A01B1
English:This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause
undesired operation of the device. CAN ICES (B) / NMB (B). French: Cet appareil contient des émetteurs/récepteurs exempts de licence qui sont
conformes aux RSS exemptés de licence d'Innovation, Sciences et Développement
économique Canada. L'exploitation est soumise aux deux conditions suivantes :
(1) Cet appareil ne doit pas provoquer d'interférences. (2) Cet appareil doit accepter toute interférence, y compris les interférences
susceptibles de provoquer un fonctionnement indésirable de l'appareil. This device meets the exemption from the routine evaluation limits in section 6.6 of
RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian
information on RF exposure and compliance. cet appareil est conforme à l'exemption des limites d'évaluation courante dans la
section 6.6 du cnr - 102 et conformité avec rss 102 de l'exposition aux rf, les 41
utilisateurs peuvent obtenir des données canadiennes sur l' exposition aux champs
rf et la conformité. This equipment complies with Canada radiation exposure limits set forth for an
uncontrolled environment. Cet équipement est conforme aux limites d'exposition aux rayonnements du Canada
établies pour un environnement non contrôlé. The device for operation in the band 5150–5350 MHz is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite systems. L'appareil destiné à fonctionner dans la bande 5150-5350 MHz est uniquement
destiné à une utilisation en intérieur afin de réduire le potentiel d'interférences
nuisibles aux systèmes mobiles par satellite cocanaux. This radio transmitter has been approved by Industry Canada to operate with the
antenna types listed with the maximum permissible gain indicated. Antenna types
not included in this list, having again greater than the maximum gain indicated for
that type, are strictly prohibited foruse with this device. Le présent émetteur radio a étéapprouvé par Industrie Canada pour fonctionner
avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain
maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. CE
Declaration of conformity
Hereby, Shenzhen Xtooltech Intelligent Co., Ltd.declares that this
Wireless Diagnostic Module is in compliance with the essential requirements and
other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2)
and Article 10(10), this product allowed to be used in all EU member states. UKCA
Hereby, Shenzhen Xtooltech Intelligent Co., Ltd. declares that this
Wireless Diagnostic Module satisfies all the technical regulations applicable to the
product within the scope of UK Radio Equipment Regulations (SI 2017/1206); UK