Turbo Care NZ Ltd

Turbo Care NZ Ltd TurboCare NZ Ltd
(1)

This Nissan Navara turbo came into us for a warranty assessment...Safe to say it didn’t take a rocket scientist long to ...
09/06/2026

This Nissan Navara turbo came into us for a warranty assessment...

Safe to say it didn’t take a rocket scientist long to figure this one out 😅




06/06/2026

🏁 RACE 1 WIN AT THE BEND! 🏆

🥇 P1 - Race Winner
🚛 #19 BDK Earthmoving Super Truck
👨‍🏁 Dale Cornfoot

Turbocharger TipWhen removing or reinstalling a compressor cover, take extra care not to contact the compressor wheel bl...
29/05/2026

Turbocharger Tip

When removing or reinstalling a compressor cover, take extra care not to contact the compressor wheel blades during assembly. It does not take much to nick, bend or damage a blade especially on tighter tolerance turbochargers.

Even minor blade damage can lead to:
Balance issues
Reduced performance
Unwanted noise
Premature turbocharger failure

A few good habits

Keep components clean
Never force the cover into place
Check alignment carefully
Rotate the assembly by hand before tightening fully

A few extra minutes and a bit of care can save a very expensive repair bill later on



This Garrett TV8101 turbo came in for a checkover today.Once we removed the turbine housing, it became pretty clear we’d...
25/05/2026

This Garrett TV8101 turbo came in for a checkover today.

Once we removed the turbine housing, it became pretty clear we’d found half the engine inside it 🤣

Unfortunately this is the result of a dropped valve, a good reminder of just how much damage engine failures can cause to a turbocharger in a very short amount of time.





A few modifications underway to fit this Evo 3 turbo in place of the old TC06 setup on a Starion.Because the factory TC0...
25/05/2026

A few modifications underway to fit this Evo 3 turbo in place of the old TC06 setup on a Starion.

Because the factory TC06 turbine housing bolts directly to the manifold, and the Evo 3 housing uses studs instead, we needed to relieve the back of the housing to allow clearance for the nuts and open the mounting holes out to 10.5mm.

Nothing too major, just a few tweaks to make everything work nicely together. Should be a great upgrade and definitely wake the old girl up.



Genuine Holset HX30WThe 6cm housing delivers excellent low RPM response and strong mid-range performance, making the HX3...
14/05/2026

Genuine Holset HX30W

The 6cm housing delivers excellent low RPM response and strong mid-range performance, making the HX30W a highly responsive and well-balanced turbo upgrade for TD42 owners.

Great setup for

• Touring builds
• Towing applications
• Off-road setups
• Daily driven Patrols & Safaris

With supporting modifications, these setups are capable of producing up to 180hp while maintaining excellent drivability and reliability.

• T3 Fl**ge
• Internally wastegated
• 44mm compressor wheel
• 52mm turbine
• Supports up to 180hp

https://turbocare.co.nz/products/genuine-holset-hx30w-6cm-turbo-nissan-td42?_pos=3&_sid=03d99a32c&_ss=r

We recently had an old-school Mazda 12A running a Hitachi HT18 turbo come into the workshop for some attention.On inspec...
07/05/2026

We recently had an old-school Mazda 12A running a Hitachi HT18 turbo come into the workshop for some attention.

On inspection, the compressor wheel was damaged.
Rather than rebuild it back to original spec, we took the opportunity to modernise the setup while retaining its character.

What we did:

Retained the original turbine wheel and turbine housing
Upgraded to a Garrett bearing housing
Fitted a Garrett compressor wheel and cover
Machined to suit and assembled in house

The result: a stronger, more efficient setup while still keeping the original HT18 foundation.




This IHI 9VA06 turbocharger came in for inspection from an Audi A3 due to actuator fault codes.Inspection identified sig...
06/05/2026

This IHI 9VA06 turbocharger came in for inspection from an Audi A3 due to actuator fault codes.

Inspection identified significant wear in the actuator valve guide, causing the actuator to operate outside its calibrated range and trigger fault codes.

This is a commonly observed wear-related fault on this style of Audi/VW turbocharger.



When it comes to ball bearing turbos, the differences aren’t always visible but they’re criticalThe graph to the right s...
02/05/2026

When it comes to ball bearing turbos, the differences aren’t always visible but they’re critical
The graph to the right shows three consecutive balance runs on one of our TCRX ball bearing units. Notice how the lines track almost identical across the entire RPM range. That level of consistency is what we try aim for every build.
Ball bearing turbos are far more sensitive to balance than journal bearing units
There’s far less tolerance for variation so any slight imbalance, misalignment, or machining inconsistency shows up immediately at speed.

They demand:

* Extremely high quality components
* Precision machining across the entire rotating assembly
* A correctly engineered bearing pack
* Attention to detail when assembling

That’s why we take the time to ensure every unit is assembled and tested to the same standard. When everything is right you get clean, repeatable balance every single run.
That consistency is what delivers reliability and performance when it matters most.
Consistency like this doesn’t happen by accident it’s built into every unit.




21/04/2026

Address

4 Langstone Lane Papanui
Christchurch
8052

Opening Hours

Monday 8am - 5:30pm
Tuesday 8am - 5:30pm
Wednesday 8am - 5:30pm
Thursday 8:30am - 5:30pm
Friday 8:30am - 5:30pm
Saturday 9am - 1pm

Alerts

Be the first to know and let us send you an email when Turbo Care NZ Ltd posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Share